The slot dimensions (used on handguards, etc.) are available on the web. The slots provide metric 20 mm (0.79 in) length intervals, and accessories can be mounted either within a slot or bridging between slots, making it possible to adjust the position of accessories in smaller intervals than the length of the slot. The slots on an M-Lok handguard are approximately 32 mm (1.260 in) long and 7 mm (0.276 in) wide. Able to provide an answer. How about slots longer than 13/16' × 1 7/8'? I would assume that it would be treated as a long slot. Question sent to AISC's Steel Solutions Center Nominal hole dimensions for standard, oversized, short-slotted and long-slotted holes are given in Table J3.3 of the 2005 AISC.
Larger cars are an issue when the size of the bay is fixed. Automobile associations warn of this issue. A Swiss Association regulating parking space wants to consider this issue for 2016. needs update In the United Kingdom, the recommended standard parallel bay size is 2.4 metres (7.9 ft) wide by 4.8 metres (16 ft) long. Slotted Standard 1-5/8 in x 1-5/8 in Strut Channel, Pre-Galvanized Steel, 12 ga., 1 ft. Country of Origin USA. Country of Origin is subject to change. This Metal Framing Strut Channel was engineered to provide maximum support with minimal pieces and labor.
American National Standard Machine Screws and Machine Screw Nuts
This Standard ANSI B18.6.3 covers both slotted and recessed head machine screws. Dimensions of various types of slotted machine screws, machine screw nuts, and header points are given in Tables 1 through 12. The Standard also covers flat trim head, oval trim head and drilled fillister head machine screws and gives cross recess dimensions and gaging dimensions for all types of machine screw heads. Information on metric machine screws B18.6.7M is given beginning on page 1708.
Threads
Except for sizes 0000, 000, and 00, machine screw threads may be either Unified Coarse (UNC) and Fine thread (UNF) Class 2A (see American Standard for Unified Screw Threads starting on page 1865) or UNRC and UNRF Series, at option of manufacturer. Thread dimensions for sizes 0000, 000, and 00 are given in Table 7 on page 1698.
Threads for hexagon machine screw nuts may be either UNC or UNF, Class 2B, and for square machine screw nuts are UNC Class 2B.
Length of Thread
Machine screws of sizes No. 5 and smaller with nominal lengths equal to 3 diameters and shorter have full form threads extending to within 1 pitch (thread) of the bearing surface of the head, or closer, if practicable. Nominal lengths greater than 3 diameters, up to and including 1 1⁄8 inch, have full form threads extending to within two pitches (threads) of the bearing surface of the head, or closer, if practicable. Unless otherwise specified, screws of longer nominal length have a minimum length of full form thread of 1.00 inch. Machine screws of sizes No. 6 and larger with nominal length equal to 3 diameters and shorter have full form threads extending to within 1 pitch (thread) of the bearing surface of the head, or closer, if practicable. Nominal lengths greater than 3 diameters, up to and including 2 inches, have full form threads extending to within 2 pitches (threads) of the bearing surface of the head, or closer, if practicable. Screws of longer nominal length, unless otherwise specified, have a minimum length of full form thread of 1.50 inches.
Table 1. Square and Hexagon Machine Screw Nuts ANSI B18.6.3-1972 (R1991)
All dimensions in inches. Hexagon machine screw nuts have tops flat and chamfered. Diameter of top circle should be the maximum width across flats within a tolerance of minus 15 percent. Bottoms are flat but may be chamfered if so specified. Square machine screw nuts have tops and bottoms flat without chamfer.
Diameter of Body
The diameter of machine screw bodies is not less than Class 2A thread minimum pitch diameter nor greater than the basic major diameter of the thread. Cross-recessed trim head machine screws not threaded to the head have an 0.062 in. minimum length shoulder under the head with diameter limits as specified in the dimensional tables in the standard.
Designation
Machine screws are designated by the following data in the sequence shown: Nominal size (number, fraction, or decimal equivalent); threads per inch; nominal length (fraction or decimal equivalent); product name, including head type and driving provision; header point, if desired; material; and protective finish, if required. For example:
- ¼ - 20 × 1 ¼ Slotted Pan Head Machine Screw, Steel, Zinc Plated
- 6 - 32 × ¾ Type IA Cross Recessed Fillister Head Machine Screw, Brass
Machine screw nuts are designated by the following data in the sequence shown: Nominal size (number, fraction, or decimal equivalent); threads per inch; product name; material; and protective finish, if required. For example:
- 10 - 24 Hexagon Machine Screw Nut, Steel, Zinc Plated
- 0.138 - 32 Square Machine Screw Nut, Brass
Table 2. American National Standard Slotted 100-Degree Flat Countersunk Head Machine Screws ANSI B18.6.3-1972 (R1977)
a When specifying nominal size in decimals, zeros preceding the decimal point and in the fourth decimal place are omitted.
All dimensions are in inches.
Table 3. American National Standard Slotted Flat Countersunk Head and Close Tolerance 100-Degree Flat Countersunk Head Machine Screws ANSI B18.6.3-1972 (R1991)
a When specifying nominal size in decimals, zeros preceding the decimal point and in the fourth decimal place are omitted.
b These lengths or shorter are undercut.
c May be rounded or flat.
All dimensions are in inches.
Table 4. American National Standard Slotted Undercut Flat Countersunk Head and Plain and Slotted Hex Washer Head Machine Screws ANSI B18.6.3-1972 (R1991)
a When specifying nominal size in decimals, zeros preceding the decimal point and in the fourth decimal place are omitted.
b These lengths or shorter are undercut.
a Unless otherwise specified, hexagon washer head machine screws are not slotted.
All dimensions are in inches.
American National Standard Machine Screws and Machine Screw Nuts
This Standard ANSI B18.6.3 covers both slotted and recessed head machine screws. Dimensions of various types of slotted machine screws, machine screw nuts, and header points are given in Tables 1 through 12. The Standard also covers flat trim head, oval trim head and drilled fillister head machine screws and gives cross recess dimensions and gaging dimensions for all types of machine screw heads. Information on metric machine screws B18.6.7M is given beginning on page 1708.
Threads
Except for sizes 0000, 000, and 00, machine screw threads may be either Unified Coarse (UNC) and Fine thread (UNF) Class 2A (see American Standard for Unified Screw Threads starting on page 1865) or UNRC and UNRF Series, at option of manufacturer. Thread dimensions for sizes 0000, 000, and 00 are given in Table 7 on page 1698.
Threads for hexagon machine screw nuts may be either UNC or UNF, Class 2B, and for square machine screw nuts are UNC Class 2B.
Length of Thread
Machine screws of sizes No. 5 and smaller with nominal lengths equal to 3 diameters and shorter have full form threads extending to within 1 pitch (thread) of the bearing surface of the head, or closer, if practicable. Nominal lengths greater than 3 diameters, up to and including 1 1⁄8 inch, have full form threads extending to within two pitches (threads) of the bearing surface of the head, or closer, if practicable. Unless otherwise specified, screws of longer nominal length have a minimum length of full form thread of 1.00 inch. Machine screws of sizes No. 6 and larger with nominal length equal to 3 diameters and shorter have full form threads extending to within 1 pitch (thread) of the bearing surface of the head, or closer, if practicable. Nominal lengths greater than 3 diameters, up to and including 2 inches, have full form threads extending to within 2 pitches (threads) of the bearing surface of the head, or closer, if practicable. Screws of longer nominal length, unless otherwise specified, have a minimum length of full form thread of 1.50 inches.
Table 1. Square and Hexagon Machine Screw Nuts ANSI B18.6.3-1972 (R1991)
All dimensions in inches. Hexagon machine screw nuts have tops flat and chamfered. Diameter of top circle should be the maximum width across flats within a tolerance of minus 15 percent. Bottoms are flat but may be chamfered if so specified. Square machine screw nuts have tops and bottoms flat without chamfer.
Diameter of Body
The diameter of machine screw bodies is not less than Class 2A thread minimum pitch diameter nor greater than the basic major diameter of the thread. Cross-recessed trim head machine screws not threaded to the head have an 0.062 in. minimum length shoulder under the head with diameter limits as specified in the dimensional tables in the standard.
Designation
Machine screws are designated by the following data in the sequence shown: Nominal size (number, fraction, or decimal equivalent); threads per inch; nominal length (fraction or decimal equivalent); product name, including head type and driving provision; header point, if desired; material; and protective finish, if required. For example:
- ¼ - 20 × 1 ¼ Slotted Pan Head Machine Screw, Steel, Zinc Plated
- 6 - 32 × ¾ Type IA Cross Recessed Fillister Head Machine Screw, Brass
Machine screw nuts are designated by the following data in the sequence shown: Nominal size (number, fraction, or decimal equivalent); threads per inch; product name; material; and protective finish, if required. For example:
- 10 - 24 Hexagon Machine Screw Nut, Steel, Zinc Plated
- 0.138 - 32 Square Machine Screw Nut, Brass
Table 2. American National Standard Slotted 100-Degree Flat Countersunk Head Machine Screws ANSI B18.6.3-1972 (R1977)
a When specifying nominal size in decimals, zeros preceding the decimal point and in the fourth decimal place are omitted.
All dimensions are in inches.
Table 3. American National Standard Slotted Flat Countersunk Head and Close Tolerance 100-Degree Flat Countersunk Head Machine Screws ANSI B18.6.3-1972 (R1991)
a When specifying nominal size in decimals, zeros preceding the decimal point and in the fourth decimal place are omitted.
b These lengths or shorter are undercut.
c May be rounded or flat.
All dimensions are in inches.
Table 4. American National Standard Slotted Undercut Flat Countersunk Head and Plain and Slotted Hex Washer Head Machine Screws ANSI B18.6.3-1972 (R1991)
a When specifying nominal size in decimals, zeros preceding the decimal point and in the fourth decimal place are omitted.
b These lengths or shorter are undercut.
a Unless otherwise specified, hexagon washer head machine screws are not slotted.
All dimensions are in inches.
Table 5. American National Standard Slotted Truss Head and Plain and Slotted Hexagon Head Machine Screws ANSI B18.6.3-1972 (R1991)
a Where specifying nominal size in decimals, zeros preceding decimal points and in the fourth decimal place are omitted.
a Unless otherwise specified, hexagon head machine screws are not slotted.
All dimensions are in inches.
Table 6. American National Standard Slotted Pan Head Machine Screws ANSI B18.6.3-1972 (R1991)
a Where specifying nominal size in decimals, zeros preceding decimal and in the fourth decimal place are omitted.
All dimensions are in inches.
Table 7. Nos. 0000, 000 and 00 Threads ANSI B18.6.3-1972 (R1991) Appendix
a Where specifying nominal size in decimals, zeros preceding decimal and in the fourth decimal place are omitted.
b There is no allowance provided on the external threads.
c The minor diameter limits for internal threads are not specified, they being determined by the amount of thread engagement necessary to satisfy the strength requirements and tapping performance in the intended application.
All dimensions are in inches.
Table 8. American National Standard Slotted Fillister and Slotted Drilled Fillister Head Machine Screws ANSI B18.6.3-1972 (R1991)
All dimensions are in inches.
1 Where specifying nominal size in decimals, zeros preceding decimal points and in the fourth decimal place are omitted.
2 Drilled hole shall be approximately perpendicular to the axis of slot and may be permitted to break through bottom of the slot. Edges of the hole shall be free from burrs.
3 A slight rounding of the edges at periphery of head is permissible provided the diameter of the bearing circle is equal to no less than 90 percent of the specified minimum head diameter.
Table 9. American National Standard Slotted Oval Countersunk Head Machine Screws ANSI B18.6.3-1972 (R1991)
Slot Hole Sizes
a When specifying nominal size in decimals, zeros preceding decimal points and in the fourth decimal place are omitted.
b These lengths or shorter are undercut.
All dimensions are in inches.
Table 10. American National Standard Header Points for Machine Screws before Threading ANSI B18.6.3-1972 (R1991)
All dimensions in inches. Edges of point may be rounded and end of point need not be flat nor perpendicular to shank. Machine screws normally have plain sheared ends but when specified may have header points, as shown above.
Table 11. American National Standard Slotted Binding Head and Slotted Undercut Oval Countersunk Head Machine Screws ANSI B18.6.3-1972 (R1991)
a Where specifying nominal size in decimals, zeros preceding decimal points and in the fourth decimal place are omitted.
b Unless otherwise specified, slotted binding head machine screws are not undercut.
a These lengths or shorter are undercut.
Standard Slot Sizes
All dimensions are in inches.
Table 12. Slotted Round Head Machine Screws ANSI B18.6.3-1972 (R1991) Appendix
a When specifying nominal size in decimals, zeros preceding decimal point and in the fourth decimal place are omitted.
All dimensions are in inches.
Use this exclusive Virgin Casino promo code VIBONUS25 and get $25 on the house, no deposit required. Plus, get up to $100 cash back with this special offer from the Virgin online casino! Remember, Virgin Casino is currently only available online in NJ. Virgin Casino Promo Code 2020: VIRGINMAX (Up to $100 Real Cashback) Virgin Casino is offering a unique welcome offer for all new players. Here's all you need to about their promo codes and new user bonuses for 2020. Virgin Online Casino promo code — 2020 As a newbie, you'll receive $30 free when you create your first account at Virgin Online Casino NJ. By using our secure sign-up link and promo code, the free credits will be deposited to your account and available instantly. Save money on things you want with a Virgin Games promo code or coupon. 6 Virgin Games coupons now on RetailMeNot. Categories Log in Join for free. Virgin Games Coupon Codes. Submit a Coupon. Save with 6 Virgin Games Offers. Casino games, including poker and roulette. Play for free or profit. Today's Virgin Games Top Offers. Virgin casino promo code.
Not recommended, use Pan Head machine screws.
Machine Screw Cross Recesses
Four cross recesses, Types I, IA, II, and III, may be used in lieu of slots in machine screw heads. Dimensions for recess diameter M, width N, and depth T (not shown above) together with recess penetration gaging depths are given in American National Standard ANSI B18.6.3-1972 (R1991) for machine screws, and in ANSI/ASME B18.6.7M-1985 for metric machine screws.
ANSI Cross Recesses for Machine Screws and Metric Machine Screw
Summary
This article presents information about standard machine screws and nuts, including the different types and tables of sizes with key dimensions. Learn more about fasteners from the Machinery's Handbook, 30th Edition, which is published and available from Industrial Press on Amazon.
Other Machining Articles
More from Hardware
Thomas Industry Update
Stay up to date on industry news and trends, product announcements and the latest innovations.
Related Resources
Website Basics For Manufacturers & Industrial Companies [With Examples]
This New Device Packs a Full Computer into a Keyboard
UPS Boosts Dry Ice, Freezer Capabilities Ahead of COVID-19 Vaccine Distribution
U.K.'s #1 Kitchen Retailer to Establish Pennsylvania Headquarters
As FDA Finalizes COVID-19 Vaccine Approval, Ultra Low Temperature Freezer Sourcing Surges
Browse by Category
